User Tools

Site Tools


moai-checkup

Differences

This shows you the differences between two versions of the page.

Link to this comparison view

Both sides previous revision Previous revision
Next revision
Previous revision
moai-checkup [2017/12/06 07:11]
peopoly
moai-checkup [2018/10/31 23:14] (current)
peopoly
Line 2: Line 2:
  
  
-Hardware check up+**Hardware check up**
  
-Z-Axis and Build Platform ​+**Z-Axis and Build Platform**
  
 Please check these screws. 8 on the Build Plate Arm, 2 on z-axis from the front side.  6 on the build platform that is holding the vat. (3 on each side) Please check these screws. 8 on the Build Plate Arm, 2 on z-axis from the front side.  6 on the build platform that is holding the vat. (3 on each side)
Line 16: Line 16:
 You can also use common engine oil like 5w-30 to lubricate the Z-axis rod.  ​ You can also use common engine oil like 5w-30 to lubricate the Z-axis rod.  ​
  
-Tilt Mechanism ​+---- 
 + 
 + 
 +**Tilt Mechanism** 
 + 
 +This is the most frequent area of problem for users and the most comprehensive part of the check guide. 
 + 
 +A frequent installation mistake in the black metal part of platform going into the Silver Metal piece in not center and it would rub against each other during layer change / peeling.  
 + 
 +{{:​metal-siliver-check.png?​nolink&​400|}} 
 + 
 + 
 +This is also a good time to make sure the Platform is centered and not rubbing against Platform Cover. You can adjust the Platform by loosing the screws on the Silver colored brackets on each end of the metal bar. 
 + 
 +{{:​platform-cover-check.jpg?​nolink&​400|}} 
 + 
 +You can center the black metal piece and the Platform by moving the Platform via loosening the screws on the Silver colored brackets on each end of the metal bar  
 + 
 +{{:​adjust-silverbracket1.png?​nolink&​400|}}{{:​adjust-silverbracket2.png?​nolink&​400|}} 
 + 
 + 
 +---- 
 + 
  
 Check these 6 screws to make sure they are fully tightened, and the metal rod is locked. This is what you will see when looking in from the left frame side: Check these 6 screws to make sure they are fully tightened, and the metal rod is locked. This is what you will see when looking in from the left frame side:
  
 {{:​moai-metal_rode_check.jpg?​nolink&​600|}} {{:​moai-metal_rode_check.jpg?​nolink&​600|}}
 +
 +Make sure these parts of platform are secured too
 +
 +{{:​moai-platform-lock1.jpg?​nolink&​400|}}
 +{{:​moai-platform-lock2.jpg?​nolink&​400|}}
  
  
Line 27: Line 55:
 {{:​moai-pm_motor_check1.jpg?​nolink&​400|}} {{:​moai-pm_motor_check1.jpg?​nolink&​400|}}
  
-and see the rod in the PM motor is straight+Also check these screws ​and see the rod in the PM motor is straight. **DO NOT** use engine oil to lubricate PM motor!
  
 {{:​moai-pm_motor_check2.jpg?​nolink&​400|}} {{:​moai-pm_motor_check2.jpg?​nolink&​400|}}
  
  
-System Check Up+Move the build plate to see if it touches the cover. If it does, it may cause sudden layer shift: 
 + 
 +{{:​platform_check.png?​nolink&​400|}} 
 + 
 + 
 +Check the acrylic cover and galvo mirrors and make sure they are not dusty or covered 
 + 
 +{{:​galvo-cover.jpg?​nolink&​400|}} 
 + 
 + 
 +**Laser and Galvo position** 
 + 
 +Check the laser / galvo and see if they are mounted in the correct position. The tip of laser head should be flat on the fixture, not sticking out and sunk in.  Please also make sure both X/Y Galvos are pushed in all the way in their sockets. 
 +  
 +{{:​laser-galvo-check.jpg?​nolink&​400|}} 
 + 
 +You learn about how to adjust their positions in the [[https://​drive.google.com/​open?​id=17EYM9WTy9HMLh6x3lLFIOnQ_dxqDnTRWgukOVBkIxvg|advanced calibration guide]] 
 + 
 +**System Check Up**
  
 Update Firmware update to the latest ​ Update Firmware update to the latest ​
 please visit [[https://​peopoly.dozuki.com/​Guide/​Moai+-+Firmware+Upgrade/​3|Moai Firmware Update guide]] please visit [[https://​peopoly.dozuki.com/​Guide/​Moai+-+Firmware+Upgrade/​3|Moai Firmware Update guide]]
  
-Make sure Setting is the latest: +Make sure Setting is the latest: ​[[moai-system-setting|Current Settings ​and Profiles]]
-https://​forum.peopoly.net/​t/​latest-settings-profiles-and-documents/​234+
  
 Make sure your Cura is the latest by uninstall, cleaning and then update to the latest Cura at Make sure your Cura is the latest by uninstall, cleaning and then update to the latest Cura at
Line 44: Line 89:
  
  
-Calibration+**Calibration**
  
-Redo Leveling using our improved [[moai:​leveling|Leveling Guide.]]+Check Leveling using our improved [[moai:​leveling|Leveling Guide.]]
  
 If you find your prints are distorted on the X/Y plane, please follow [[ If you find your prints are distorted on the X/Y plane, please follow [[
Line 52: Line 97:
 |advanced calibration guide]] |advanced calibration guide]]
  
-Printing and Post Processing+**Printing and Post Processing**
  
 Make sure your printing temperature is at least 20C (68F) and ideally 25C (77F). You can learn more about resin'​s properties and best ways to clean and cure here in the [[moai:​resin|Moai Resin Wiki]] Make sure your printing temperature is at least 20C (68F) and ideally 25C (77F). You can learn more about resin'​s properties and best ways to clean and cure here in the [[moai:​resin|Moai Resin Wiki]]
  
-Software+**Software**
  
 We have made numerous update to software recommendation. For advanced users, B9 is a great tool, and XYZware / Flashforge offers great software for automatic support generation. ​ For more information,​ check out the [[moai:​software|Moai Software Wiki.]] We have made numerous update to software recommendation. For advanced users, B9 is a great tool, and XYZware / Flashforge offers great software for automatic support generation. ​ For more information,​ check out the [[moai:​software|Moai Software Wiki.]]
  
  
moai-checkup.1512565878.txt.gz · Last modified: 2017/12/06 07:11 by peopoly