User Tools

Site Tools


moai-checkup

Differences

This shows you the differences between two versions of the page.

Link to this comparison view

Both sides previous revision Previous revision
Next revision
Previous revision
moai-checkup [2018/04/24 23:50]
peopoly
moai-checkup [2018/10/31 23:14] (current)
peopoly
Line 4: Line 4:
 **Hardware check up** **Hardware check up**
  
-**Z-Axis and Build Platform ​ +**Z-Axis and Build Platform** 
-**+
 Please check these screws. 8 on the Build Plate Arm, 2 on z-axis from the front side.  6 on the build platform that is holding the vat. (3 on each side) Please check these screws. 8 on the Build Plate Arm, 2 on z-axis from the front side.  6 on the build platform that is holding the vat. (3 on each side)
  
Line 16: Line 16:
 You can also use common engine oil like 5w-30 to lubricate the Z-axis rod.  ​ You can also use common engine oil like 5w-30 to lubricate the Z-axis rod.  ​
  
-**Tilt Mechanism ​ +---- 
-**+ 
 + 
 +**Tilt Mechanism** 
 + 
 +This is the most frequent area of problem for users and the most comprehensive part of the check guide. 
 + 
 +A frequent installation mistake in the black metal part of platform going into the Silver Metal piece in not center and it would rub against each other during layer change / peeling.  
 + 
 +{{:​metal-siliver-check.png?​nolink&​400|}} 
 + 
 + 
 +This is also a good time to make sure the Platform is centered and not rubbing against Platform Cover. You can adjust the Platform by loosing the screws on the Silver colored brackets on each end of the metal bar. 
 + 
 +{{:​platform-cover-check.jpg?​nolink&​400|}} 
 + 
 +You can center the black metal piece and the Platform by moving the Platform via loosening the screws on the Silver colored brackets on each end of the metal bar  
 + 
 +{{:​adjust-silverbracket1.png?​nolink&​400|}}{{:​adjust-silverbracket2.png?​nolink&​400|}} 
 + 
 + 
 +---- 
 + 
 + 
 Check these 6 screws to make sure they are fully tightened, and the metal rod is locked. This is what you will see when looking in from the left frame side: Check these 6 screws to make sure they are fully tightened, and the metal rod is locked. This is what you will see when looking in from the left frame side:
  
 {{:​moai-metal_rode_check.jpg?​nolink&​600|}} {{:​moai-metal_rode_check.jpg?​nolink&​600|}}
 +
 +Make sure these parts of platform are secured too
 +
 +{{:​moai-platform-lock1.jpg?​nolink&​400|}}
 +{{:​moai-platform-lock2.jpg?​nolink&​400|}}
  
  
Line 27: Line 55:
 {{:​moai-pm_motor_check1.jpg?​nolink&​400|}} {{:​moai-pm_motor_check1.jpg?​nolink&​400|}}
  
-and see the rod in the PM motor is straight. DO NOT use engine oil to lubricate PM motor!+Also check these screws ​and see the rod in the PM motor is straight. ​**DO NOT** use engine oil to lubricate PM motor!
  
 {{:​moai-pm_motor_check2.jpg?​nolink&​400|}} {{:​moai-pm_motor_check2.jpg?​nolink&​400|}}
 +
 +
 +Move the build plate to see if it touches the cover. If it does, it may cause sudden layer shift:
 +
 +{{:​platform_check.png?​nolink&​400|}}
  
  
Line 37: Line 70:
  
  
-**Laser and Galvo position +**Laser and Galvo position** 
-**+
 Check the laser / galvo and see if they are mounted in the correct position. The tip of laser head should be flat on the fixture, not sticking out and sunk in.  Please also make sure both X/Y Galvos are pushed in all the way in their sockets. Check the laser / galvo and see if they are mounted in the correct position. The tip of laser head should be flat on the fixture, not sticking out and sunk in.  Please also make sure both X/Y Galvos are pushed in all the way in their sockets.
    
Line 45: Line 78:
 You learn about how to adjust their positions in the [[https://​drive.google.com/​open?​id=17EYM9WTy9HMLh6x3lLFIOnQ_dxqDnTRWgukOVBkIxvg|advanced calibration guide]] You learn about how to adjust their positions in the [[https://​drive.google.com/​open?​id=17EYM9WTy9HMLh6x3lLFIOnQ_dxqDnTRWgukOVBkIxvg|advanced calibration guide]]
  
-**System Check Up +**System Check Up** 
-**+
 Update Firmware update to the latest ​ Update Firmware update to the latest ​
 please visit [[https://​peopoly.dozuki.com/​Guide/​Moai+-+Firmware+Upgrade/​3|Moai Firmware Update guide]] please visit [[https://​peopoly.dozuki.com/​Guide/​Moai+-+Firmware+Upgrade/​3|Moai Firmware Update guide]]
  
-Make sure Setting is the latest: +Make sure Setting is the latest: ​[[moai-system-setting|Current Settings ​and Profiles]]
-https://​forum.peopoly.net/​t/​latest-settings-profiles-and-documents/​234+
  
 Make sure your Cura is the latest by uninstall, cleaning and then update to the latest Cura at Make sure your Cura is the latest by uninstall, cleaning and then update to the latest Cura at
Line 65: Line 97:
 |advanced calibration guide]] |advanced calibration guide]]
  
-**Printing and Post Processing +**Printing and Post Processing** 
-**+
 Make sure your printing temperature is at least 20C (68F) and ideally 25C (77F). You can learn more about resin'​s properties and best ways to clean and cure here in the [[moai:​resin|Moai Resin Wiki]] Make sure your printing temperature is at least 20C (68F) and ideally 25C (77F). You can learn more about resin'​s properties and best ways to clean and cure here in the [[moai:​resin|Moai Resin Wiki]]
  
moai-checkup.1524631800.txt.gz · Last modified: 2018/04/24 23:50 by peopoly