User Tools

Site Tools


moai:firmware

Differences

This shows you the differences between two versions of the page.

Link to this comparison view

Both sides previous revision Previous revision
Next revision
Previous revision
moai:firmware [2018/05/15 21:29]
peopoly
moai:firmware [2019/09/26 07:36] (current)
peopoly
Line 1: Line 1:
 ====== Firmware ====== ====== Firmware ======
  
-===== Current firmware is v1.16 released on March 31st 2018 =====+===== Current firmware is v1.18 released on September 12th 2018 =====
  
-If you are not on this version, [[https://​peopoly.dozuki.com/​Guide/​Moai+-+Firmware+Upgrade/​3|Use this guide]] for the instructions and a link to the firmware. If you just want the firmware without the instructions use [[https://​drive.google.com/​open?​id=1acyCMmZVfjTXCHmD3HkSovGj2zGli0Nu|This link for the firmware file]]+If you are not on this version, [[https://​peopoly.dozuki.com/​Guide/​Moai+-+Firmware+Upgrade/​3|Use this guide]] for the instructions and a link to the firmware. If you just want the firmware without the instructions use [[https://​drive.google.com/​open?​id=1-KjPhXRP3WK202ryUa9ex77GtBlO_LUy|This link for the firmware file]]
  
 If you want to learn about what these settings mean, please refer to [[moai:​moai|Settings Menu]] If you want to learn about what these settings mean, please refer to [[moai:​moai|Settings Menu]]
Line 9: Line 9:
  
 ==== Latest System Setting ==== ==== Latest System Setting ====
 +**latest update 9/​28/​2018** 
 +**these are for Moai with PDMS vat only, NOT Moai 200**
 System Setup: System Setup:
   * X Size 900   * X Size 900
Line 16: Line 17:
   * Y Deviation 100   * Y Deviation 100
   * Smooth 50   * Smooth 50
-  * Z Motor Speed 6 +  * Z Motor Speed 2 
-  * PM Motor Speed 20+  * PM Motor Speed 15
  
 Advanced Setting Advanced Setting
Line 23: Line 24:
   * XY Speed Set 4   * XY Speed Set 4
   * Z Reset Position 1877   * Z Reset Position 1877
-  * PM Reset Position ​40 +  * PM Reset Position ​10 
-  * Z Follows ​40+  * Z Follows ​2
   * CompensateX 100   * CompensateX 100
   * CompensateY 200   * CompensateY 200
 +  * Z Initial Speed 2    ​
 +  * PM Initial Speed 10
  
-Firmware 1.16 calibration guide:+ 
 +---- 
 + 
 +**Recommended Moai with FEP vat Firmware setting 
 +** 
 + 
 +System Setup: 
 +  * X Size 900 
 +  * Y Size 900 
 +  * X Deviation 100 
 +  * Y Deviation 100 
 +  * Smooth 50 
 +  * Z Motor Speed 2 
 +  * **PM Motor Speed 12**  /latest change 
 + 
 +Advanced Setting 
 +  * Laser Power 58 
 +  * XY Speed Set 4 
 +  * Z Reset Position 1817 (this depends on how user level but normally 1815-1820 
 +  * **PM Reset Position 60** 
 +  * Z Follows 2 
 +  * CompensateX 100 
 +  * CompensateY 200 
 +  * Z Initial Speed 2     
 +  * **PM Initial Speed 10 
 +** 
 + 
 + 
 +**For a description of what these settings mean, [[moai:​moai#​settings|go here]].** 
 + 
 +Firmware 1.16 (if you are coming from 1.15 or lower) ​calibration guide:
  
   - Record current 1.15 settings, especially if you have any custom settings.   - Record current 1.15 settings, especially if you have any custom settings.
Line 38: Line 71:
  
 ==== Changelog ==== ==== Changelog ====
 +
 +  * 1.18
 +      * added Print Time duration
 +      * Improved SD card I/O performance
 +      * Allows putting gcode in any of the subdirectories in the root directory. ​
 +      * updated to the latest settings. ​
  
   * 1.16   * 1.16
Line 55: Line 94:
     * Calibration     * Calibration
     * Accuracy improvements     * Accuracy improvements
 +
 +==== Beta Firmware (updated 4/27/2019) ====
 +
 +Experimental Moai firmware with the extended gcode command (For researcher and developer, do not use for regular print production)
 +
 +firmware [[https://​drive.google.com/​open?​id=1v5-FTYrWJVOeYmi2q74ZgIkFu8K4UdXo|download]]
 +discussion
 +
 +Overview: The extended gcode command allows finer control of Moai during printing. The changes to settings is only temporary for the duration of the current gcode file and will not be saved to the system settings. ​ The command can be inserted at any point of the gcode file as long as it has its own line. The firmware will still work with existing gcode exported from Asura or Cura that do not contain any extended gcode command. ​
 +
 +Setting definition change
 +  * Z-Follow 0-60 each unit represents 0.1mm the range of value is (-1) to (5)
 +  * Z-Follow 0 = -1 mm movement upward during peel
 +  * Z-Follow 60 = 5 mm movement downward during peel
 +
 +For recommended z-follow for general printing, it is now 30 (2mm downward movement)
 +
 +
 +Commands:
 +
 +  * M1001 X40 ;laser power change to 40
 +  * M1002 X5 ;wait for 5 seconds before continuing ​
 +  * M1003 X1800 ;moving build platform arm to z-axis reset spot of 1800 (in the setting) or 180mm down from the top
 +  * M1004 X50 ;peel motion ​ 50 has no meaning
 +  * M1005 X10 ;change Pm moto speed to 10
 +  * M1006 X3 ;change Z Motor Speed to 3
 +  * M1007 X12 ;change Z Follows (distance) to 12
 +  * M1008 X15 ;change PM Reset Position to 15
moai/firmware.1526437774.txt.gz · Last modified: 2018/05/15 21:29 by peopoly